Home > Products

AC Pd Volatge Withstand Test Set/ Hipot Tester for

  • RF08 Mini Series-modular Get Price!

    Service cart for SF6-gas handling of small to medium size gas-insulated equipment.

  • RF051 Economy Series SF6 Gas Handling Cart Get Price!

    For easy maintenance on high voltage switchgear Less than 220kv

  • RF391 Mega Series SF6 Gas Handling Unit Get Price!

    Maintenance device for large and extra large gas compartments.

  • RF300 SF6 Gas Purification for re-use System Get Price!

    SF6 recycling and re-use

  • S100 Micro Series SF6 Gas Recycling Device Get Price!

    Special application Recovery of a small amount of sf6 gas in a small SF6 Gas compartments.

  • RFJ SF6 Refilling Evacuating Devices Get Price!

    SF6 Gas Cylinder to Gas compartments

  • RA912 SF6 Gas Analyzer Get Price!

    For determining the quality of SF6 gas.he RA912 multi-functional analyzer allows the determination of up to seis quality parameters with only one measurement:SF6 concentration (%).Moisture concentration.SO2 concentration (ppmv).CO concentration (ppmv).H2S concentration (ppmv).Option: HF concentration (ppmv)

  • NA1013 SF6 Gas Monitoring System Get Price!

    For continuous monitoring of the SF6 quality.NA-1013 online infrared gas transmitter is base on the internet of things’s air quality monitoring instruments .It used online monitoring for toxic gases, SF6 gas, O2, temperature, humidity, etc. Fast response, high accuracy, with a variety of selectable signal output mode.Passed through the third grade EMC industry test. Compliance with IEEE 802.15.4 wireless communication standard, ZigBee communication protocol support

  • Smart SF6 Sensor Get Price!

    NDIR SF6 Sensor 10 years life for SF6 Gas Leakage detection.Measurement principle: Dual wavelength, Non Dispersive Infra-Red (NDIR).Measurement range: 0-50/1000/1500ppm.Gas supply: by diffusion (atmospheric pressure).Warm-up time: < 2 minutes (start-up time).< 11 minutes (fade in finished).< 30 minutes (full specification).Measuring response.Response time (t90): appr. 60 s.Digital resolution (@ zero): 1 ppm.Repeatability: ≤ ± 15 ppm.

  • Product Introduction & Features:It is mainly used for testing frequency voltage insulation level of various insulation materials, insulation structure and electrical products, also as partial discharge frequency testing power supply for testing object such as transformer, mutual inductor and lightni
    • What is HIPOT Testing (Dielectric Strength Test)?Get Price!

      12/16/2019· A minor disadvantage of the ac hipot tester is that if the circuit under test has large values of Y capacitors, then, depending on the current trip setting of the hipot tester, the ac tester could indicate a failure. Most safety standards allow the user to disconnect the Y capacitors prior to testing or, alternatively, to use a dc hipot tester.

    • High Voltage AC Withstand & Diagnostic Methods Using Very.Get Price!

      · PDF 文件affordable AC test equipment. A 100 lb. VLF hipot can do the job of a multi-ton Series Resonant or 60 Hz output power supply. VLF stands for Very Low Frequency. A VLF test set is an instrument that produces an AC high voltage output but at a frequency of 0.1 Hz or lower. It is simply an AC hipot but with a frequency output much lower than

    • Dielectric withstand test - WikipediaGet Price!

      A dielectric withstand test or high potential or hipot test is an electrical test performed on a component or product to determine the effectiveness of its insulation.The test may be between mutually insulated sections of a part or energized parts and electrical ground. The test is a means to qualify a device's ability to operate safely during rated electrical conditions.

    • The Basics of VLF Testing | HV TECHNOLOGIES, Inc.Get Price!

      Very low frequency (VLF) withstand testing is the application of an AC sinusoidal waveform, generally at 0.01 – 0.1 Hz, to assess the quality of electrical insulation in high capacitive loads, such as cables. During the test cables are subjected to a test voltage significantly higher than what they experience during normal operating conditions.

    • Very Low Frequency (VLF) Withstand Testing - The BasicsGet Price!

      3/3/2016· A Very Low Frequency (VLF) Withstand Test is an AC Withstand Test usually carried out at a frequency between 0.1 Hz and 0.01 Hz. This kind of test is suited for testing high capacitance loads such.

    • Power Cable Testing and Diagnostics OverviewGet Price!

      5/2/2018· One advantage of a DC hipot test is that the leakage-current trip points can be set to a much lower value than that of an AC voltage test. In the past, DC dielectric withstand testing has been the most widely used test for acceptance and maintenance of cables.




    Email: [email protected]

    Send your Inquiry

    Inquiry

    Using our contact forms you can also send inquiries, give feedback, request information and ask questions.
    Email:
    [email protected]